PocketWizard Used Pocketwizard Flextt5 – Canon | Used Lighting

The Canon Dedicated Pocket Wizard Flextt5 Transceiver, With Its Built In Hot-Shoe And Controltl Firmware, Is The Perfect Addition To Canon E-Ttl Ii Flash Systems. The Flextt5 Takes The Existing Benefits Of Canon Wireless Systems Beyond The Boundaries Of Infrared Technology. When Paired With The Mini Tt1 Transmitter Or Another Flextt5 Transceiver, A Whole New World Of Wireless Flash Freedom Opens Up. The Flextt5 Is Also The Perfect Transceiver For Your Manual Triggering Needs And Works With All Multimax Channels And Many Of The Multimax Advanced Functions. Please Note: Not Compatible With The Canon 1Dx Ii

Please Note
The Pocketwizard Flextt5 – Canon Is Not Fully Compatible With The New Canon Eos 6D Mkii And Eos 1Dx Mkii. For Owners Of These Cameras, The New Pocketwizard Flextt6 – Canon Will Provide Full Compatibility.

The Flextt5’S Simple Design Comes To Life Through Its Hot-Shoe Connection With A Camera Or Flash. Mount A Flash Or Command Unit On The Flextt5 To Use The Same Zone Controls And Ratio Commands As You Would Normally.The System Tracks Your Changes In Iso, Shutter Speed And Aperture And Reacts Accordingly To Make Sure Exposures Stay Right On Target.Use The Flash Compensation Dial On Your Camera Or Flash Just As You Would Normally And The Changes Pass Seamlessly Through The System.

The Flextt5 Has Two Channel Configuration Settings; C1 And C2. Each Can Be Programmed As Needed With Up To 20 Controltl Channels For Ttl Photography, Or 32 Standard Channels For Manual Flash Photography. The Flextt5 Transceiver Also Has A Three-Zone Selector Switch For Ease Of Use With Canon Zones And Ratios.

With Pocketwizard Hypersync™ Technology, The Flextt5 Can Precisely Advance The Timing Of Your Flash Trigger So That Increased Flash Sync Speeds, Up To 1/500Th Of A Second Is Achievable With Many Strobes.

Need More Speed? Push Your Controltl System Beyond 1/500Th And Go Into Fp/High-Speed Sync Mode Automatically. Simply Change Your Shutter Speed To Get Flash Sync All The Way To 1/8000Th.No Buttons To Press Or Settings To Change!

A Pocketwizard Utility Program Is Provided To Support The Flextt5 Transceiver Via A Usb Port. The Utility Allows You To Configure Your Channel Settings, Dial In Your Hypersync Timing, Adjust Your Sleep-Mode Timers As Well As Update Your Product To The Latest Firmware.

The Flextt5 Also Has Our Auto-Sensing Transceiver Technology That Enables It To Switch Back And Forth Between Transmitter And Receiver Modes As Needed For Greater Flexibility On The Job. When A Hot-Shoe Or Other Trigger Is Detected, It Automatically Switches To Transmitter Mode.With Auto Relay Mode You Can Easily Trigger A Remote Camera In Sync With Remote Flash. Put A Camera Where You Can’T Be And Use Remote Ttl Or Non-Ttl Lighting At The Same Time. Expand Your Coverage And Increase Your Creativity.

Ttl Compatibility Canon E-Ttl Ii

Frequency: 433.42 – 434.42 Mhz, Ce

Channels: 35 Channels Over 5 Frequencies

Antenna: 2.7″ (6.9 Cm) Rubberized With 180 Degree Swing

Transmit Output Power: Less Than 0.001 Watt (1/1000 Of A Watt Or 1 Milliwatt)

Range Performance: 30 To 800 Feet (10 To 240 Meters) For E-Ttl Ii Triggering Depending On Flash Used, Antenna Orientation And Other Variables.
30 To 1200 Feet (10 To 365 Meters) For Basic Triggering Depending On Flash Used, Antenna Orientation And Other Variables.
For More Info, Click Here.

Mounting: Hot Shoe, 1/4-20, Lanyard, Velcro

Maximum Shooting Rate Frames Per Second (Fps) 8 Fps For E-Ttl Ii And Normal Triggering

Power / Channel Switch Off – C.2 – C.1

Zone Select Switch A-B-C (Matches Canon Slave Groups)

Status Indicator Led: Green, Amber, Red Status Indications

Camera / P1 Port 1/8″ (3.5 Mm) Stereo Miniphone For 2-Stage Remote Camera Triggering. Port Voltage Handling: Up To 50 Volts, 100 Milliamp Continuous
Tip = Trigger
Ring = Pre-Trigger
Sleeve = Ground

Flash / P2 Port
1/8″ (3.5 Mm) Mono Miniphone. Port Voltage Handling: Up To 200 Volts, 4 Amps Peak, 250 Milliamp Continuous, Non-Polarized

Minimum Receive Contact Time Camera / P1 Port = 80 Milliseconds Flash / P2 Port = 500Us

Voltage Present 3.3 Vdc (All Pins) – Safe For All Cameras

Hot Shoe Voltage Protection: Hot Shoe: Up To 50V

Usb: Usb Compliant 2.0, Mini-B Connector, 5Vdc Regulated, 100Ma, Pin 1 Positive, Pin 4 Ground

Operating Temperature Above -15° C (5° F) And Below 50° C (120° F).

Storage Temperature (Without Battery) Above -30 C (-22 F) And Below 85 C (185 F)

Construction High Impact Plastic, Captive Battery Door
Hot Shoe Made Of Glass Reinforced Resin

Power
Two (2) Aa (Iec:Lr6) Alkaline Recommended, Other Chemistries (Nimh, Nicad, Lithium) Allowed, Usb

Battery Life 60 + Hours

Dimensions 3.6″ (9.2 Cm) Long X 2.9″ (7.3 Cm) Wide X 1.4″ (3.6 Cm) Tall, Antenna Lowered

Weight 5.4 Oz (153 Grams) 3.8 Oz (108 Grams) Without Batteries

Included In The Box Flextt5 Transceiver, Usb Cable, Two (2) Aa Batteries, Quick Guide